MIELE TROUBLESHOOTING
Miele Dryer
Error Codes
Start with the code on your appliance. Understand what it means, check the likely causes, and find a clear next step.
37 supported error codes
FIND YOUR CODE
What does your appliance display?
Match the code exactly. Open a guide for its meaning, first checks, and manufacturer reference.
Showing all 37 codes
The dryer is in Demo Mode, so the drying program will not start.
View troubleshooting guide ADDADD means the dryer door can be opened to add or remove laundry.
View troubleshooting guide Clean Door FilterThe dryer is requesting that the door lint filter be cleaned.
View troubleshooting guide Clean Out AirwaysThe dryer detected reduced airflow through the filter or air path.
View troubleshooting guide CtrlCtrl indicates that the Remote control function is active and the dryer is connected through the Miele app/cloud.
View troubleshooting guide Empty Out ContainerThe dryer condensate container needs attention.
View troubleshooting guide F1Miele lists F1 as a valid dryer diagnostic fault. The exact component or cause can vary by model.
View troubleshooting guide F104The voltage applied to the drive motor is too low.
View troubleshooting guide F108Miele reports an electronic fault.
View troubleshooting guide F156Refrigerant temperature sensor downstream of condenser short-circuited.
View troubleshooting guide F157Refrigerant temperature sensor downstream of condenser open-circuited.
View troubleshooting guide F158The appliance has overheated.
View troubleshooting guide F159There is a compressor start-up fault.
View troubleshooting guide F2Miele lists F2 as a valid dryer diagnostic fault. The exact component or cause can vary by model.
View troubleshooting guide F206Refrigerant temperature sensor downstream of compressor short-circuited.
View troubleshooting guide F207Refrigerant temperature sensor downstream of compressor open-circuited.
View troubleshooting guide F242Miele reports an electronic fault.
View troubleshooting guide F252The dryer door contacts near the hinge are dirty.
View troubleshooting guide F3Miele lists F3 as a valid dryer diagnostic fault. The exact component or cause can vary by model.
View troubleshooting guide F30Door signal and door contact signal are different.
View troubleshooting guide F36Door contact (reed switch) is faulty.
View troubleshooting guide F38Miele reports an electronic fault.
View troubleshooting guide F39Miele reports an electronic fault.
View troubleshooting guide F4Miele lists F4 as a valid dryer diagnostic fault. The exact component or cause can vary by model.
View troubleshooting guide F40Miele reports an electronic fault.
View troubleshooting guide F41Miele reports an electronic fault.
View troubleshooting guide F43Model type not programmed/incorrect variant set.
View troubleshooting guide F45Miele reports an electronic fault.
View troubleshooting guide F46Miele reports an electronic fault.
View troubleshooting guide F50The dryer drum may be overloaded; F50 can also appear about 1 minute after the door has been opened, or from a software fault.
View troubleshooting guide F53The drive motor is faulty/there is an electronic fault.
View troubleshooting guide F55The laundry is still damp after the maximum 180-minute drying time on a residual-moisture program.
View troubleshooting guide F66The dryer airflow is restricted, most often because the lint filters or plinth/toe-kick filter are dirty, wet, damaged, or airflow around the dryer is obstructed.
View troubleshooting guide F99The appliance is blocked.
View troubleshooting guide noCnoC means no Connection while MobileStart is selected.
View troubleshooting guide Red Filter IndicatorThe dryer is requesting filter or airflow maintenance.
View troubleshooting guide Technical FaultThe dryer shows Technical fault with no obvious cause; Miele directs you to power-cycle the dryer and thoroughly clean the airflow filters and heat-exchanger area.
View troubleshooting guideNo matching codes. Try the exact code on the display, or clear the filter to browse all guides.
A CLEAR NEXT STEP
A little context helps.
Keep your model number and the exact displayed code nearby. Code meanings and instructions can vary by model; compare each guide with your appliance’s manual.
Guides combine manufacturer references with plain-language explanations. Follow the guide’s safety precautions and stop if a check requires work you’re not comfortable doing.