APPLIANCE TROUBLESHOOTING
Whirlpool Front Load Washer Error Codes
Find plain-language explanations for WhirlpoolFront Load Washer error codes, common causes, and troubleshooting steps you can try before requesting repair service.
67 error codes currently available
10h
The washer Delay Start feature is set for approximately 10 hours.
View error details →
11h
The washer Delay Start feature is set for approximately 11 hours.
View error details →
12h
Whirlpool indicates a number followed by h is not an error; it means Delay Wash is activated.
View error details →
1h
The washer Delay Start feature is set for approximately 1 hour.
View error details →
2h
The washer Delay Start feature is set for approximately 2 hours.
View error details →
3h
The washer Delay Start feature is set for approximately 3 hours.
View error details →
4h
The washer Delay Start feature is set for approximately 4 hours.
View error details →
5h
The washer Delay Start feature is set for approximately 5 hours.
View error details →
6h
The washer Delay Start feature is set for approximately 6 hours.
View error details →
7h
The washer Delay Start feature is set for approximately 7 hours.
View error details →
8h
The washer Delay Start feature is set for approximately 8 hours.
View error details →
9h
The washer Delay Start feature is set for approximately 9 hours.
View error details →
CL
The washer is reminding you to run the Clean Washer cycle.
View error details →
dET
dET means the detergent cartridge is not detected in the dispenser.
View error details →
Detergent Low
Whirlpool indicates Detergent Low means more detergent needs to be added to the bulk dispenser.
View error details →
F0 E1
Whirlpool indicates F0 E1 or rL means the Clean Washer cycle was started while the washer detected a load inside.
View error details →
F0 E2
Whirlpool indicates F0 E2 means the washer detected excessive suds in the washer basket.
View error details →
F0 E3
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F0 E4
Whirlpool indicates the washer senses that the water temperature is too hot.
View error details →
F0 E5
Whirlpool indicates the washer detected an off-balance load. An unbalanced load can reduce spin speed, lengthen the cycle, and leave clothing wetter than expected.
View error details →
F0 E7
Whirlpool indicates F0 E7 means clothing was detected while the washer was attempting to run the Clean Washer cycle.
View error details →
F1 E1
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F1 E2
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F2 E1
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F2 E2
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F20
Whirlpool indicates F20 means the washer has a water inlet problem because no water or insufficient water is entering the washer.
View error details →
F21
Whirlpool indicates F21 means the washer has a drain problem.
View error details →
F22
Whirlpool indicates a front-door lock issue. The door may not be fully closed, the lock may have buildup around it, or the load may be preventing the door from closing completely.
View error details →
F3 E1
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F3 E2
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F3 E3
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F3 E5
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F3 E6
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F4 E1
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F4 E4
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F5 E1
Whirlpool indicates a washer door-switch issue.
View error details →
F5 E2
F5 E2 means the washer door is not locking properly.
View error details →
F5 E3
Whirlpool indicates the washer door is not locking properly. Something may be blocking the latch or preventing the door from closing.
View error details →
F5 E4
Whirlpool indicates the washer has completed three consecutive cycles without the door being opened.
View error details →
F6 E1
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F6 E2
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F6 E3
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E1
F7 E1 is a motor-speed sensing error; the motor cannot reach the correct speed for the selected cycle.
View error details →
F7 E2
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E3
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E6
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E7
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E8
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 E9
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 EA
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
F7 EC
Whirlpool indicates the washer is overloaded.
View error details →
F8 E1 / LO FL
F8 E1 or LO FL means the washer is sensing low water flow.
View error details →
F8 E2
F8 E2 indicates a problem with the dispenser system.
View error details →
F8 E3
Whirlpool indicates F8 E3 is an overflow condition caused by too much water or foam in the washer.
View error details →
F9 E1
F9 E1 means the washer is taking longer than expected to drain, typically more than 8 minutes.
View error details →
FC E0
Whirlpool recommends resetting the front-load washer control for this code before further troubleshooting.
View error details →
FH
Whirlpool identifies FH as a water-supply problem on the front-load washer.
View error details →
Int
Int means the wash cycle was paused or canceled and the washer is stopping and draining.
View error details →
LC
Control Lock is activated.
View error details →
Lo FL
Whirlpool indicates Lo FL means the washer is not detecting the correct amount of incoming water.
View error details →
LOC / LC
LOC or LC means Control Lock is active.
View error details →
No Water Detected
The washer is not detecting the expected incoming water.
View error details →
PF
Whirlpool identifies PF as a power failure that occurred while the washer was operating.
View error details →
rL
Laundry was detected during the Clean Washer cycle.
View error details →
rL / F34
F34 means items were detected in the washer during the Clean Washer cycle.
View error details →
Sd
The washer detected excessive detergent suds.
View error details →
Sud / Sd
SUD or Sd means the washer detected too many suds.
View error details →
Manufacturer information
ApplianceSignal troubleshooting information is based on manufacturer support documentation and rewritten in plain language.