APPLIANCE TROUBLESHOOTING
Miele Washer Error Codes
Find plain-language explanations for MieleWasher error codes, common causes, and troubleshooting steps you can try before requesting repair service.
59 error codes currently available
Check Detergent
Check detergent means too much detergent was used.
View error details →
Check Inlet
The washer is not receiving enough water.
View error details →
Drain
The washer is reporting a water drainage fault because the drain is restricted.
View error details →
F1
Miele lists F1 as a valid washer diagnostic fault. The exact component or cause can vary by model.
View error details →
F10
The washer water inlet is blocked or restricted.
View error details →
F103
Miele reports a fault with the M-Bus module.
View error details →
F104
Miele reports a fault with the drum drive.
View error details →
F105
Miele reports a fault with the steam generator.
View error details →
F106
Miele reports a fault with the steam generator.
View error details →
F11
The washer drain is restricted by hose installation/kinks or a blocked drain filter/pump.
View error details →
F130
Miele reports a fault with the electronic.
View error details →
F131
Miele reports a fault with the electronic of the external dispenser unit.
View error details →
F138
The Miele Waterproof System detected a leak and water is present in the drip tray.
View error details →
F139
There is water in the housing of the external dispenser unit.
View error details →
F140
The water level is too high in the mixing container of the external dispenser unit.
View error details →
F15
The washer hot-water inlet is blocked or restricted.
View error details →
F16
The washer detected too much detergent/detergent additive, an unsuitable wash program, or excessive foam.
View error details →
F19
Flow meter stiff.
View error details →
F199
There is a fault affecting the connection between the washing machine and XCI box.
View error details →
F2
Miele lists F2 as a valid washer diagnostic fault. The exact component or cause can vary by model.
View error details →
F20
The washer Thermostop/heating system did not reach the required temperature in time; a heating fault may be present.
View error details →
F210
The washer suds-circulation system is restricted by lint at the door-seal nozzle or a blocked drain filter/pump.
View error details →
F211
You can continue to use the washing machine with manual dispensing. TwinDos thermocouple sensor short-circuited, container 1.
View error details →
F212
You can continue to use the washing machine with manual dispensing. TwinDos thermocouple sensor open-circuited, container 1.
View error details →
F213
You can continue to use the washing machine with manual dispensing. TwinDos thermocouple sensor short-circuited, container 2.
View error details →
F214
You can continue to use the washing machine with manual dispensing. Technical fault: TwinDos thermocouple sensor open-circuited, container 2.
View error details →
F220
The washing machine is leaking.
View error details →
F242
There is a communication fault between the touch display and electronic.
View error details →
F252
The door contacts near the washer/washer-dryer hinge are dirty.
View error details →
F29
Miele reports a fault with the steam generator.
View error details →
F3
Miele lists F3 as a valid washer diagnostic fault. The exact component or cause can vary by model.
View error details →
F34
The washer cannot lock the door/drum; overloading or a technical fault may be involved.
View error details →
F35
The washer cannot unlock the door/drum or the door lock is jammed.
View error details →
F37
The washer is not level or the drain hose is installed too high.
View error details →
F373
A leak was detected around the drain filter because the filter is not tightened correctly.
View error details →
F39
Miele reports a fault with the electronic.
View error details →
F4
Miele lists F4 as a valid washer diagnostic fault. The exact component or cause can vary by model.
View error details →
F41
The washer electronics reported a technical fault.
View error details →
F43
Miele reports a fault with the electronic.
View error details →
F44
Miele reports a fault with the electronic.
View error details →
F45
Miele reports a fault with the electronic.
View error details →
F47
Miele reports a fault with the electronic.
View error details →
F49
Miele reports a fault with the electronic.
View error details →
F50
Miele reports a fault with the drum drive.
View error details →
F51
Miele reports a fault with the pressure sensor.
View error details →
F53
Miele reports a fault with the drum drive.
View error details →
F56
The final-spin speed was below 400 rpm, often because excessive detergent produced too much foam.
View error details →
F62
The program selector is between defined settings.
View error details →
F63
Miele reports a fault with the water path control unit.
View error details →
F64
Miele reports a fault with the magnetic field sensor.
View error details →
F65
Miele reports a fault with the drum lighting.
View error details →
F81
Miele reports a fault with the steam generator.
View error details →
F83
Miele reports a fault with the steam generator.
View error details →
F92
Long-term use of only low-temperature programs can allow bacteria to develop in the washer.
View error details →
Locked
Locked means the washer safety lock is active, so temperature, spin speed, or options cannot be changed during the program.
View error details →
noC
noC means no Connection while MobileStart is selected.
View error details →
Technical Fault
The washer display is reporting a technical fault.
View error details →
Water Inlet Fault
Water Inlet Fault means the washer water inlet is blocked or restricted.
View error details →
Waterproof System Activated
The Miele Waterproof System detected an internal leak.
View error details →
Manufacturer information
ApplianceSignal troubleshooting information is based on manufacturer support documentation and rewritten in plain language.